Required Tools and Supplies:
- 6mm Allen Socket
- 8mm Socket
- Torque Wrench
- 2.5-inch Oil Filter Wrench
- Grease Gun
- Oil pan
- PS-4 Engine Oil
- Drain Plug Washer
- Oil Filter
- All Terrain Grease
- Eye Protection
- Nitrile Gloves
- Shop Rags
To learn more about tools, read the Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Polaris RZR. Always check and change the oil and filter at the intervals outlined in the Periodic Maintenance Chart in your Owner's Manual. The PS-4 Full Synthetic Oil Change Kit is part number 2879323.
To change the engine oil and filter on your model year 2021 and newer RZR Trail S 1000, follow these steps.
1. Park the vehicle on a flat, level surface in a well-ventilated area, and ensure the transmission is in PARK.
2. Start the engine and allow it to warm up at idle for 2 to 3 minutes. Then stop the engine.
3. Pull up on the cargo box panel latch, and pivot it up to remove.
4. Clean the area around the oil cap.
5. Remove the oil cap, and set it aside.
6. Place a drain pan underneath the engine crankcase. Placing a rag in the bottom of the drain pan will help prevent the splashing of oil.
7. Clean the area around the oil drain plug.
8. Remove the drain plug with a 6mm Allen socket and allow the oil to drain completely. This process will take approximately 15 minutes.
9. Remove the engine access panel by pulling and pivoting out.
10. Before continuing, position a shop towel underneath the oil filter to catch spillage.
11. Using a 2.5-inch oil filter wrench, turn the oil filter counterclockwise to remove.
12. Using a clean dry cloth, clean the filter sealing surface on the crankcase, and ensure the old O-ring is completely removed.
13. Lubricate the O-ring on the new filter with a film of fresh engine oil, and ensure the O-ring is in good condition.
14. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface. Then turn it an additional three-quarters of a turn. The filter is part number 2540086.
15. Once the filter is installed, wipe up any residual oil. Ensure there are no shop towels left on the engine.
16. Clean any dirt or debris from the drain plug, and ensure the sealing surfaces are free of any burrs, nicks or scratches.
17. Install a new drain plug washer on the drain plug. The drain plug washer is part number 5812232.
18. Reinstall the drain plug. Torque to 12 ft-lbs (16 Nm).
19. Before continuing, clean any residual oil off the vehicle.
20. Add the proper amount of the recommended oil through the oil fill cap. Do not overfill. The capacity is 2.5 quarts (2.4 L). PS-4 Full Synthetic 5W-50 Oil is part number 2876244 for 1 quart (946 mL) and part number 2876245 for 1 gallon (3.78 L). PS-4 Extreme Duty Full Synthetic 10W-50 Oil is part number 2878920 for 1 quart (946 mL) and part number 2878919 for 1 gallon (3.78 L).
21. Reinstall the oil fill cap, and wipe up any residual oil.
22. Start the engine, and allow it to idle for 1 to 2 minutes.
23. Stop the engine, and inspect the vehicle for leaks.
24. Remove the dipstick and wipe with a clean shop towel. Then reinstall the dipstick fully and remove again to inspect the oil level. Add oil as needed to bring the level to the upper mark on the dipstick.
25. Reinstall the dipstick, and wipe up any residual oil.
26. Reinstall the access panel by aligning the top retaining tabs and pressing on the bottom to secure.
27. Reinstall the cargo box panel by engaging the retaining tabs and locking into place. Then firmly press down on the panel to engage the latch.
28. Before continuing, dispose of the used oil and filter properly at your local recycling center.
29. Use a grease gun to grease all suspension grease zerks. Your vehicle has grease zerks located on the front sway bar mounts, rear sway bar mounts and the prop shaft.
30. Move to the rear of the vehicle to clean the spark arrestor. Note: Allow the vehicle to cool completely before performing any spark arrestor maintenance.
31. Remove the spark arrestor fastener and nut with an 8mm socket.
32. Carefully pull the spark arrestor out of the exhaust, and clean any debris on the screen.
33. Inspect the screen for wear or damage and replace if necessary. The spark arrestor is part number 1262123.
34. Reinstall the spark arrestor into the exhaust and align the mounting hole.
35. Reinstall the spark arrestor nut and fastener. Torque the fastener to 9 to 11 ft-lbs (12 to 15 Nm).
36. Once complete, the maintenance reminder can be reset in the instrument cluster. To reset the maintenance reminder, do the following:
- Turn the ignition switch ON.
- Press and hold the Mode button to enter the options menu.
- Navigate to remaining service hours and press the Mode button to reset them.
- Using the directional arrows, select your desired service hours until the next service, and press the Mode button to confirm.
- Navigate to exit and press the Mode button to return to the main screen.
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
More maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
WALKER EVANS RACING is a registered trademark of Walker Evans Enterprises Incorporated
YouTube® is a registered trademark of Google Inc.
© 2022 Polaris Inc.