Required Tools and Supplies
PS-4 Full Synthetic 5W-50 4-Cycle Oil
|6mm Allen Socket||Oil Filter Wrench|
|Oil Pan||Shop Rags|
|Safety Glasses||Nitrile Gloves|
To learn more about tools, read the Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Polaris RZR. Always check and change the oil at the intervals outlined in the Periodic Maintenance Chart in your Owner's Manual. To change the oil and filter on your RZR 800, RZR 4 800, RZR S 800, RANGER RZR or RANGER RZR S, follow these steps.
The engine drain plug is located on the bottom of the crankcase. The oil dipstick and fill tube is located on the engine, behind the passenger seat. On RZR 4 models, it is behind the right rear passenger seat. To access it, remove the seats and rear service panel.
1. Position the vehicle on a level surface in a well-ventilated area. Place the transmission in PARK. Apply the brakes.
2. Start the engine. Allow it to idle for 2 to 3 minutes. Stop the engine.
3. Remove the seats to gain access to the oil dipstick and fill tube.
- Pull up on the seat latch lever located under the rear edge of the seat.
- Tilt the seat forward.
- Lift the seat upward to remove it from the vehicle.
4. Remove the rear service panel, which is located behind the seats and on the frame of the vehicle.
5. Clean the area around the drain plug. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin.
6. Place a drain pan beneath engine crankcase and remove the drain plug with a 6mm Allen socket.
7. Allow the oil to drain completely.
8. Inspect the sealing surfaces on the drain plug and crankcase for burrs, nicks or scratches. Install a new sealing washer on the drain plug. The sealing washer is part number 5812232.
9. Reinstall the drain plug. Torque to 16 ft-lbs. (22 Nm).
10. Using a cap-style oil filter wrench, turn the filter counterclockwise to remove it.
11. Using a clean dry cloth, clean the filter sealing surface on the crankcase.
12. Lubricate the O-ring on the new filter with a film of fresh engine oil. Make sure the O-ring is in good condition. Replace it if necessary. The O-ring is part number 5413013.
13. Install the new filter and turn by hand until the filter gasket contacts the sealing surface. Then turn it an additional three-quarters of a turn. The filter is part number 1240482.
14. Remove the dipstick and fill the sump with 2 quarts (1.9 L) of the recommended oil. Polaris PS-4 Full Synthetic 5W50 4-Cycle Oil is part number 2876244 for 1 quart (0.95 L) and part number 2876245 for 1 gallon (3.8 L). Polaris PS-4 Extreme Duty Synthetic 10W50 4-Cycle Oil is part number 2878920 for 1 quart (0.95 L) and part number 2878919 for 1 gallon (3.8 L).
15. Start the engine. Allow it to idle for 1 to 2 minutes.
16. Stop the engine and inspect for leaks.
17. Check the oil level on the dipstick
- Lift the lever lock to remove the dipstick. Wipe it dry with a clean cloth.
- Reinstall the dipstick completely, but do not lock it. The dipstick must be inserted completely in to keep the angle and depth of the stick consistent.
- Remove the dipstick and check the oil level. Maintain the oil level in the safe range. Do not overfill. Tip: Due to the dipstick entry angle into the crankcase, the oil level will read higher on the bottom side of the dipstick. Always read the level on the upper surface of the dipstick.
- Reinstall the dipstick. Seat the lever lock.
18. Dispose of used filter and oil properly.
19. Reinstall the rear service panel.
20. Reinstall the seats. Make sure the seat tabs at the front edge of the seat slide under the seat retainer bar. Press down firmly at the rear of the seat to engage the rear latch.
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.